4. Space Screws Appropriately Proper spacing of the screws ensures an even distribution of load and enhances stability in the assembly.
One of the primary benefits of using 2-inch self-drilling screws is the time savings they offer. In projects where speed is essential, these screws can significantly reduce the overall construction time. Without the need to pre-drill holes, workers can quickly set up and fasten materials together, increasing productivity. This is particularly advantageous in situations where time constraints are a critical factor, such as in commercial construction or during emergency repairs.
Hot dip galvanizing, also known as hot dip zinc, is the method of forming a layer of zinc coating on the surface of the workpiece after oil removal and rust removal, showing a clean and infiltrating surface, immediately immersed in the plating tank of zinc melting in advance. Cold galvanizing is the same after the removal of oil, in addition to lure, showing no pollution, infiltration of the workpiece hung into a special electroplating tank on the cathode, the anode with zinc. Switch on the DC power supply, zinc ions on the anode migrate to the cathode, and discharge on the cathode, so that the workpiece is coated with a layer of zinc layer hot dip galvanizing method.
Annealing wire is widely used because it has a good elasticity and flexibility, in the annealing process can be good control of its hardness, it is mainly made of iron wire, more often used in the construction industry binding wire use. In the production of the wire factory, annealing wire will be processed according to the properties of the material, according to the needs of different to change its hardness degree, can make it has more advantages, can reduce the consumption of metal, reduce the cost of production.
Due to the influence of production process or other factors, the zinc layer of galvanized wire products will be different to a certain extent, especially ordinary galvanized can not reach the beauty of electric galvanized, ordinary galvanized wire zinc layer is mainly for anticorrosion and corrosion prevention. Large volume galvanized wire products refers to the use of high quality low carbon steel, after drawing forming, pickling rust removal, high temperature annealing, hot dip galvanized, cooling and other processes, some galvanized wire products are made of iron wire galvanized.
Dip plastic six side barbed wire corrosion lost the original characteristics, in the shape, color and mechanical properties and other aspects will change, resulting in equipment damage, pipeline leakage, in particular, is prone to fracture, lose the original protective function.
If the surface of galvanized wire hair black, galvanized layer is thin and uneven, this galvanized wire is partly because the inventory storage time is longer, it may also be because the production technical requirements of galvanized wire, do not meet the standard standards and lead to galvanized wire quality problems. According to the use of galvanized wire is different, galvanized wire has soft and hard, so the galvanized wire for binding requires the flexibility of galvanized wire is better, the flexibility of galvanized wire is good, which can facilitate the operation of workers.
Cold galvanized, generally speaking, do not need heating, galvanized amount is little, this galvanized parts are easy to fall off in wet environment. Hot dip galvanizing, also known as hot dip galvanizing, is to melt the zinc ingot at high temperature, put some auxiliary materials in, and then dip the metal structural parts into the galvanized groove, so that the metal members are attached to a layer of zinc layer. The advantage of hot dip galvanized is that its anticorrosion ability is strong, the adhesion and hardness of galvanized layer is better.
The blade gill net of plastic paint is formed after rust protection processing after the manufacture of blade type barbed iron wire rope. The periphery of blade gill net should have good rust prevention effect, the peripheral processing should be beautiful, and can be of good practical value, more convenient installation, higher cost performance and other advantages. Plastic paint is a common electrostatic coating method, which can be fixed on the periphery of chicken wire or wire plate. After two hundred heat treatment, plastic paint or powder paint is glued to the surface of wire plate. These blade gill nets coated with plastic paint are generally used on indoor boxes. The coating processing does not take too long, mainly because the effect of rust prevention and corrosion protection is quite good, much better than the general material.
There are many production links of blade barbed rope, and the finished product can only be produced after several times of production. Roughly, there are four or five links.
1. Zinc pot operators must stick to their posts
Stainless steel barbed wire is mainly used in the place near the sea more, wet salty air for metal corrosion is particularly serious, and the selection of stainless steel barbed wire is in order to prevent corrosion.
In the process of composite electroplating galvanized wire, the plating solution must be stirred to obtain the composite coating in which the particles dispersed in the matrix metal. Stirring methods include mechanical stirring, air stirring, ultrasonic stirring, bath circulation, etc. The acid activation solution in the production process can remove the corrosion products and oxide film on the surface of the low carbon steel wire without excessive corrosion on the matrix.
The first is the cost of raw materials galvanized sheet and galvanized wire, some specifications and waste calculation and so on. Then there is the cost of mechanical processing process and manual processing process. Finally, there is the cost of packing and shipping. In recent years, due to the rapid development of thorn rope manufacturers, so the profit margin of blade thorn rope is not particularly broad.
Now it is more used in the binding of the construction industry. Compared with ordinary iron wire, it is softer and has better luster. Use in daily life does not need to carry out maintenance and maintenance, save a lot of time, but also save the cost of maintenance and maintenance. Annealed wire has good stability, good corrosion resistance, greatly prolonging the service life. More kinds, can be selected according to different uses, making annealing wire device is simple, improve the utilization rate of the device. The material properties of annealed wire can meet different processing requirements.
Raw material of wire mesh sheet cold drawn low carbon steel wire base material can choose low carbon steel hot rolled disk bar or hot rolled smooth steel bar. The base material number and diameter of cold-drawn low carbon steel wire can be confirmed according to the rules in the table below. During the cold drawing process, the surface shrinkage rate of each drawing should not be greater than the wire mesh before cold drawing. Annealing shall not be carried out during wire drawing. If butt welding is required, the same production unit and base material of the same number should be selected. The appearance quality of wire mesh should not affect wire drawing. When the welding function is poor or brittle fracture occurs, special inspection should be carried out according to relevant standards.
Hexagonal mesh is a metal wire woven Angle mesh (hexagonal) made of wire mesh, the use of metal wire diameter is based on the size of the hexagonal and different. Also known as: twist flower net, stone cage net, gabion net, flood control network.
The design is designed not only for ease of installation, but also for the ability to achieve such installation in harsh terrain conditions such as cliffs, with little anchorage and little excavation for quick and easy installation. Based on the characteristics of heavy hexagonal mesh double stranded structure, even in the case of wire damage can also withstand the impact of falling rock.
