- If you think there has been an overdose, call your poison control center or get medical care right away. Be ready to tell or show what was taken, how much, and when it happened.
- The Versatile Role of HPMC in Various Industries
- The HPMC viscosity table provides a range of values that correspond to the viscosity of HPMC solutions at different concentrations. These values are typically expressed in centipoise (cP), a unit of measurement for fluid viscosity. The table allows users to select the appropriate HPMC grade based on their desired viscosity level. For example, if a formulation requires a low-viscosity solution, an HPMC grade with a lower viscosity value would be selected. Conversely, if a high-viscosity solution is needed, an HPMC grade with a higher viscosity value would be chosen.
- In the food industry, HPMC serves multiple roles
- In the pharmaceutical sector, HPMC is used as a binder, disintegrant, and coating agent in tablets, and as a suspending and viscosity-enhancing agent in liquid formulations. Its non-toxicity and stability make it an ideal choice for these applications.

redispersible polymer powder wiki. In adhesives, it can improve bonding strength and resistance to environmental factors, such as moisture and temperature fluctuations. In paints and coatings, redispersible polymer powder can enhance pigment dispersion, UV resistance, and overall film integrity.
3.2.1 Absorption, distribution, metabolism and excretion


water into a clear or slightly turbid colloidal solution
5. hydroxypropyl methyl cellulose (HPMC) in putty powder amount?
There are data for microcrystalline cellulose (E 460), methyl cellulose (E 461), hydroxypropyl cellulose (E 463) and sodium carboxymethyl cellulose (E 466), which were tested in mice, rats, hamsters and/or rabbits with oral dosing or via gavage. As regards microcrystalline cellulose (E 460) studies have been conducted in rats (dietary exposure) with a mixture including guar gum or sodium carboxymethylcellulose (E 466) (15% in either case). The NOAEL for both maternal and developmental toxicity were the highest experimental dosages, i.e. 4,500 mg/kg bw (for mixture with guar gum) and 4,600 mg/kg bw (for mixture with sodium carboxymethyl cellulose). Methyl cellulose (E 461) was examined in mice, rats, hamsters and rabbits. In two different studies, pregnant mice were exposed via gavage (vehicle corn oil) to a dose range of 16-1,600 mg methyl cellulose (E 461)/kg bw per day from day 6 to 15 of gestation, followed by a caesarean section at day 17 of gestation. In the first study, maternal toxicity (increase in mortality and reduced pregnancy rate in the survivors) as well as retarded ossification in fetuses were noticed at the highest tested level, pointing to a NOAEL of 345 mg methyl cellulose (E 461) mg/kg bw per day (the last but one highest dosage) in mice. In the second study, no maternal toxicity and fetal abnormalities were observed in mice exposed up to 700 mg methyl cellulose (E 461) mg/kg bw per day. Rat studies (n = 2) were performed in pregnant dams exposed via gavage (vehicle corn oil) to a dose range of 16-1,320 mg methyl cellulose (E 461) mg/kg bw per day from day 6 to 15 of gestation followed by a caesarean section at day 20. In the first study (0, 13, 51, 285 or 1,320 mg methyl cellulose (E 461)/kg bw per day) the highest tested dosage resulted in no maternal toxicity but also in increased incidence of extra centres of ossification in vertebrae of fetuses from high dose dams; in a second rat study, the incidence of such alteration slightly increased in fetuses from the highest dosed group (1,200 mg methyl cellulose (E 461)/kg bw per day). Based on the above results, a NOAEL of 285 mg methyl cellulose (E 461) mg/kg bw per day could be identified in rats. No maternal or fetal toxicity was detected in Golden hamsters exposed via gavage (vehicle corn oil) up to 1,000 mg methyl cellulose (E 461) mg/kg bw per day from day 6 to 10 of gestation followed by a caesarean section at day 20. The study on rabbits was discarded due to poor experimental design. The only relevant developmental toxicity study with hydroxypropyl cellulose (E 463) (dissolved in 1% gum arabic solution) was performed in pregnant rats exposed via gavage from day 7 to 17 of gestation to 0, 200, 1,000 or 5,000 mg/kg bw test item and some of them subjected to caesarean sections at day 20. No treatment-related adverse effects were detected in dams or in the examined fetuses. A number of dams were allowed to deliver and no clinical, behavioural or morphological changes were observed in the examined pups. Their reproductive ability was seemingly not affected and no abnormalities were found in the F1-derived fetuses. The in utero exposure to the highest dose (5,000 mg/kg bw per day) may be considered as the NOAEL of methyl cellulose (E 461) for this study. No mortality, and no adverse effects were observed on implantation or on fetal survival in pregnant mice or rats dosed via gavage with up to 1,600 mg sodium carboxymethyl cellulose (E 466)/kg bw per day.
