- Coating and Corrosion Resistance For outdoor or harsh environments, select bolts with the necessary coatings to prevent rust and corrosion.
3. Enhanced Performance The design facilitates even load distribution, reducing the risk of material deformation around the fastened area and ensuring a durable assembly.
- Coating For outdoor applications or in environments prone to corrosion, selecting the right coating is crucial. Galvanized or coated screws will resist rust and extend the lifespan of the fasteners.
1, stress relief before plating where the maximum tensile strength is greater than 1034Mpa key and important parts before plating should be at 200±10℃ stress relief for more than 1 hours, carburizing or surface quenching parts should be at 140±10℃ stress relief for more than 5 hours.
In sulfur dioxide, hydrogen sulfide and Marine atmosphere, zinc corrosion resistance is poor, especially in the high temperature and high humidity atmosphere containing organic acid, galvanized wire galvanized layer is easy to be corroded. The uniformity of the galvanized layer on the surface of galvanized wire and the color of galvanized wire, the galvanized layer on the surface of high-quality galvanized wire is uniform, zinc adhesion is good, and the color is white, there is no leakage plating and rust points and other problems.
The derusting steel parts are immersed in the melted zinc liquid at about 500℃, so that the surface of the steel member is attached with zinc layer, so as to achieve the purpose of anti-corrosion. The surface of galvanized wire coating can see whether the quality of galvanized wire is good or not. If the strength of zinc attached to the wire is very poor, then this galvanized wire do not buy, because this galvanized wire must be poor galvanized wire.
The steel mesh is also called longitudinal reinforcement and transverse reinforcement. The longitudinal reinforcement and transverse reinforcement are spaced at right angles to each other, and all the crossing points are welded together. It has the characteristics of crack – proof, small error and good quality. Steel mesh is mainly used in coal mine roadway, concrete pavement, bridge deck, airport runway and buildings. So, what are the advantages of mesh?
Hardness is a commonly used property index in mechanical properties of metal materials. The iron wire factory introduces a fast and economical test method for hardness testing. However, for the hardness of metal materials, there is not a unified and clear definition including all test methods at home and abroad. In general, the hardness of a metal is often considered to be the resistance of the material to plastic deformation, scratches, wear, or cutting.
Fourth, the difference between 201 and 304 is the problem of nickel. And the price of 304 is relatively expensive now, generally close to 20,000 yuan per ton, but 304 can at least ensure that it will not rust in the process of use. (Experiment with potions)
The barbed rope produced by the barbed rope factory adopts the way of winding in order to facilitate transportation, and the disk weight of the galvanized barbed rope is different according to the size.
Galvanized hook mesh standard is thorough, mesh planning: 3cm-20cm, silk planning: 1.2mm-4.5mm, galvanized hook mesh 6000 square meters, some standards are available. Benefits: The selection of low carbon steel wire, surface for cold galvanized (electric galvanized) hot dip galvanized anticorrosion treatment, mesh wire strong, strong protection, long anticorrosion time.
When laying steel wire mesh, according to the laying method from the middle to both sides in turn. Wall plastering engineering use wire mesh material is generally two kinds: one is electroplating, the other is hot dip galvanized. The former has low cost and a wide range of use. The cost of hot-dip galvanized material is slightly higher than that of electroplating, and the cost is high and the life is good to prevent rust. Hot dip galvanizing is in the case of heating plating. After the zinc is melted into liquid form, the base metal is immersed in it so that the zinc interpenetrates with the base metal and binds so tightly that there are no other impurities or defects left in the process.
Electric galvanized wire is dipped in the zinc solution of heating ablation, the production speed is fast, the coating is thick but not uniform, the market allows a low thickness of 45 microns, up to 300 microns or more. The color is dark, the zinc metal is consumed, and the matrix metal is formed into the entry layer, the corrosion resistance is good, and the outdoor environment of hot dip galvanized can adhere to decades.
The production process of stainless steel blade and galvanized blade is basically similar. The blade size is usually determined according to the mold.
One: according to the color of the spray blade thorn rope, its price is higher than the ordinary blade thorn rope 2000-2200 yuan, but the price ratio of the spray blade thorn rope is much higher.
And high quality data is constrained by production cost and production conditions, so some welding mesh manufacturers do not meet this requirement, natural in this case, there is no way to improve the strength of the product. In addition to the data, there is the production process, even if it is the best data, but the manufacturer does not meet the production process requirements in the welding, it will also form the product under high pressure welding, so this is also a decline in strength, the process conditions of different manufacturers are also very different, so it forms the market above the product has a difference in strength.